Aquabot Bravo Repair Manual

  



  1. See Full List On Aquadist.com
  2. Aquabot Bravo Parts Diagram

Repair Manual For Dodge Intrepid. Comments: Aquabot Repair Guide. I am looking for the o-rings or gaskets for my aquabot drive motor. I repair termimals and broken wire but it leaks from the terminals. Did you check the link pointed out in the accepted answer? Proper lubricating oil is good to go. View and Download Aquabot Robotic Pool Cleaner operating instructions manual online. Robotic Pool Cleaner. Robotic Pool Cleaner swimming pool vacuum pdf manual download.

Bravo
yugreat.netlify.com › Aquabot Bravo Repair Manual ▆ ▆

You can purchase parts for these pool cleaners here: How To Disassemble Aquabot Turbo Taking a Pool. Aquabot Repair; Blue Diamond Repair; Dolphin Repair; Polaris Repair; TigerShark Repair; Kreepy Krauly Repair. Aquabot Bravo Parts; Aquabot Viva Parts; Cobia XL Parts.

  • Aquabot Pool Rover Hybrid Above Ground Automatic Swimming Pool Cleaner APRV

    $399.99

    Shipping: + $79.97 Shipping

  • Aquabot Pura 4XT pool rover pool vacuum robotic no motor

    $99.99

    Shipping: + $60.32 Shipping

  • Aquabot Swimming Pool Cleaning Robot Rover T Cleaner APRTR1 New Condition

    $199.95

    Shipping: + $169.29 Shipping

  • Aquabot Rover S2-40 AJET121 Above Ground Robotic Auto Pool Cleaner (Open Box)

    $284.99

    $389.99

    Shipping: + $67.47 Shipping

  • AQUABOT JR IN GROUND AUTOMATIC SWIMMING POOL VACUUM CLEANER PUMP WALLS & STEPS

    $695.00

    Shipping: + $79.66 Shipping

  • Aquabot Mamba Above & In-Ground Suction Side Automatic Swimming Pool Cleaner

    $77.39

    $89.59

    Shipping: + $40.03 Shipping

I have an aquabot pool cleaner and pump motor stopped working. If you disassemble it the oil inside runs out. I really only need to know what type of oil to use to replace it. The 35V motor has 4 capacitors to jump start it. I have replaced the capacitors once before in my own machine without loosing the oil and reusing it. Successful long term repair accomplished. This one is a relatives of mine who lost the oil and I don't want to replace capacitors, only to ruin successful job by putting the wrong oil in it. Does anyone know what type of can be used in this motor?

Answered! View the answer I have this problem too Subscribed to new answers

Is this a good question?

Manual Auto Repair Manuals

Cancel

Repair Manual For Dodge Intrepid

Aquabot Bravo Repair Manual

Comments:

Aquabot Repair Guide

Manual

I am looking for the o-rings or gaskets for my aquabot drive motor. I repair termimals and broken wire but it leaks from the terminals. Please help

Aquabot Bravo Repair Manual

Did you check the link pointed out in the accepted answer?

Proper lubricating oil is good to go. If you need suggestions or service on this please visit a website https://www.hammerheads.ae/

Hello,

I have a robotic pool pump, part number AS00035R and it has stop functioning, I was going to replace the entire pump, but looking at some of the previous comments, it appears this pump can be dismantled and repaired? Never have done this previously, how hard is it to perform? I'm worried I will ruin it by doing something wrong. Any advice?

It is unlikely that both Motors (Drive Motor – Ref.# 1.15 and Pump Motor – Ref.# 1.14) are experiencing mechanical problems. In most cases the issue lies with something that is hindering the flow of electricity from the electrical outlet to the Power Supply (Figure 4) or through the Floating Cable (Ref.# 3.1) to the Aquabot itself. To locate and resolve where electrical flow is being hindered check the following.

Electrical Outlet & Connections – Make sure that the Power Supply is firmly plugged into a grounded electrical outlet which has power. To test the outlet, plug in another electrical instrument that you know works to the outlet.

Check that the Floating Cable is securely plugged into the Power Supply.

See Full List On Aquadist.com

Power Supply

Aquabot Bravo Parts Diagram

  • Check that the Power Supply button is pressed upwards to the “ON” position. Note: Some models have a Reset (Safety) Switch, which must be pressed each time you press the “ON” button.
  • Switch the Power Supply “Off” and “On” several times, allowing approximately 30 seconds between each“ON” and “OFF”. Remember, if your Aquabot comes equipped with a Reset Switch it must be pressed each time after pressing the “ON” button.
  • Unplug the Power Supply from the electrical outlet. Check that the Fuse in the Power Supply’s Fuse Holder (Ref.# 4.4) appears operational. If the Fuse appears burned out, then replace it with a 5 AMP SLO BLOW Fuse Please note that there are various Power Supply model types and the location of the Fuse may be in either the front or the back of your Power Supply.
  • Use a cotton swab to dry all sides of the Fuse and Fuse Holder (inside and out). Cable Assemblies – With the Power Supply unplugged, check the Power Cable (Ref.# 4.6) and the Floating Cable for cuts or damage. If you detect damage to either Cable, please contact our Customer Service Department at 1-800-845-4856.